Customer Part Installation Instructions

ADDING THE APALLINONE TO THE AUTO SENTRY PETRO IN THE ORIGINAL MODEL Tools Required Prior to performing this procedure you will need to have the following tools: #1 Flat head screw driver Time to Completion We estimate that it will take 30 minutes to perform this procedure, time will vary based...

Adding the Auto Passport All-in-one RFID Reader top the Wash Valet eXP Tools Required Prior to performing this procedure you will need to have the following tools: #1 Flat head screw driver Time to Completion We estimate that it will take 30 minutes to perform this procedure, time will vary bas...

Wiring the eKeypadfor Vacuums and Self-Serve Bays     There are two different power wiring options for the eKeypad:   Option A: 12v/24v DC Option B: PoE (Power over ethernet)   WARNING    DO NOT wire both 12v/24v DC and PoE at the same time           Please contact ICS Technical Support if any...

  Tools Required Parts Included Powering Down the Entrance Sign WARNING: Failure to turn off the Sign increases the risk of serious bodily injury or death. On the site server desktop, click on the VNC icon for the Entrance Sign. On the menu bar, click the Windows flag icon. Click the Shutdown ...

REPLACING ENTDISPLAY46CC3 IN AN ENTRANCE SIGN Tools Required Prior to performing this procedure you will need to have the following tools:  #2 Phillips screwdriver  Small flat screwdriver Time to Completion We estimate that it will take 1 hour to perform this procedure, time will vary based on ...

    Replacing USB Credit Card Reader for all Auto Sentry Models     Completion TimeEstimated time to complete this procedure is 15 minutes. Keep all hardware organized as you work. Powering Down the Auto Sentry WARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily inj...

Auto Sentry Conversion from TXP IDTech Card Reader to First Data IDTech Card Reader and Front Facing Barcode Scanner Tools Required Prior to performing this procedure you will need to have the following tools: 5/16”, 11/32” and 3/8” nut drivers or ratchets Drill with 3/16” and ½” drill bits Jig ...

Installation of the Update to the Digital Menu Sign Video Board Controller Panel       Completion Time Estimated time to complete this procedure is one hour. Keep all hardware organized as you work. WARNING: Please have a certified electrician check voltages on the power supply before installin...

ENTRANCE SIGN CONVERSIONENT1-07 to ENT1-03 byADDING A MOTHERBOARDMB03 Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver Time to Completion We estimate that it will take 15 minutes to perform this procedure, time will vary based on...

Digital Menu Sign ENT1-07 converting it to an Exit Sign ENT1-03 by adding a motherboard Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver Time to Completion We estimate that it will take 15 minutes to perform this procedure, time ...

Vandalism Deterrent Alarm Installation in the Auto Sentry flex HD         Completion Time We estimate that it will take 15 minutes to perform this procedure. Keep all hardware organizedas you work. Powering Off the Auto Sentry   WARNING: Failure to turn off the Auto Sentry increases the ris...

Auto Sentry flex upgrade from Spectrum Air TXP to IDTech VP5300           Completion Time Estimated time to complete this procedure is 2 hours. Keep all hardware organized as you work. WARNING: Please have a certified electrician check voltages on the power supply before installing new compone...

Replacing Bar Code Reader with Bar Code Scanner in an Auto Sentry Tools Required Prior to performing this procedure, you will need to have the following tools: Phillips Screw driver 3/8” nut driver or ratchet Drill with 5/32” drill bit Jigsaw Vacuum cleaner, towel Small sharp knife Small sander ...

Auto Sentry Conversion to the Bezel Credit Card Reader Tools Required Prior to performing this procedure you will need to have the following tools: Small, sharp knife 3/8” nut driver or ratchet 11/32” nut driver or ratchet Time to Completion We estimate that it will take 2 hours to perform this...

  AUTO SENTRY CPT CONDENSATE DRAIN HOSE CONFIGURATION Tools Required Prior to performing this procedure you will need to have the following tools:  11/32” nut driver or ratchet   Time to Completion We estimate that it will take 15 minutes to perform this procedure, time will vary based on ski...

CONFIGURING A GEN MEGA BILLDISPENSER CASSETTEFOR THE TOP OR BOTTOM LOCATION   Completion Time We estimate that it will take 15 minutes to perform this procedure. Keep all hardware organizedas you work. Instructions This procedure only needs to be completed if you are changing the location of the...

46” Entrance Sign Conversion Heat Exchanger to Air Conditioner Tools Required Prior to performing this procedure, you will need to have the following tools: Phillips Screw driver Small flat screw driver A second person to help with lifting the rear doors 3/8” and 11/32” nut driver or wrench T...

Entrance Sign Conversion to a New 120V Ice Qube Air Conditioner Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver Small Flat Screw driver 7/16" nut driver or ratchet Time to Completion We estimate that it will take 1 hour to perfo...

F400 BILL DISPENSER –  READING THE SENSOR CONDITONS IN RAS MODE Tools Required Prior to performing this procedure you will need to have the following tools: Dollar bill or small piece of paper Completion Time We estimate that it will take 15 minutes to perform this procedure, time will vary bas...

Fujitsu F400 Bill Dispenser Sensor Location and Cleaning           Completion Time Estimated time to complete this procedure is 30 minutes. Keep all hardware organized as you work. WARNING: Please have a certified electrician check voltages on the power supply before installing new components....

Auto Sentry Upgrade to the GBA Bill Acceptor Tools Needed Small Phillips screwdriver 11/32” nut driver or ratchet Time to Completion We estimate that it will take 30 minutes to perform this procedure, time will vary based on skill set. NOTE: Keep all hardware organized as you work. ATTENTION: ...

Entrance Sign Conversion Heat Exchanger to Air Conditioner   Tools Required Prior to performing this procedure, you will need to have the following tools: Phillips Screw driver Small flat screw driver A second person to help with lifting the rear doors 5/16” nut driver or ratchet Time to Compl...

Conversion from IDTech to TXP in Auto Sentry Petro and a New Decal Powering Down the Auto Sentry Petro WARNING: Failure to power off the Auto Sentry Petro increases the risk of serious bodily injury or death, and also causes the credit card reader to go into a tamper state which will then have to...

Auto Sentry Conversion adding IDTech Card Readers to an Auto Sentry Super flex Tools Required Prior to performing this procedure you will need to have the following tools: 3/8” nut driver or ratchet 11/32” nut driver or ratchet 5/16” nut driver or ratchet Small, sharp knife Time to Completion T...

APALLDISBOX – USING THE RFID READER IN A LANE WITH NO AUTO SENTRY   Tools Required Prior to performing this procedure you will need to have the following tools: Flat head screw driver Time to Completion We estimate that it will take 15 minutes to perform this procedure, time will vary based on ...

MDS SENSOR POT LEVEL ADJUSTMENT ON A FUJITSU F400 BILL DISPENSER Tools Required Prior to performing this procedure, you will need to have the following tools: #2 Phillips screw driver Flat head screw driver Time to Completion We estimate that it will take 10 minutes to perform this procedure, t...

Auto Sentry eXP Install the Coin Acceptor Tools Required Prior to performing this procedure, have the following tools available: Phillips Screw driver 3/8” nut driver or ratchet 11/32” nut driver or ratchet Sharp hobby knife Time to Completion We estimate that it will take 1 hour to perform thi...

Auto Sentry ExP Install the Coin Hopper Tools Required Prior to performing this procedure you will need to have the following tools: #2 Phillips Screw driver 3/8”, 11/32”, 5/16”, and ¼” nut drivers or ratchet Time to Completion ICS estimates that it will take 2 hours to perform this procedure, ...

Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver 5/16” nut driver or ratchet Small flat screw driver Wire cutter Time to Completion We estimate that it will take 30 minutes to perform this procedure, time will vary based on skill...

Installing the RFID Auto Passport, RFID All-In-One Reader Antenna to an Auto Sentry flex       Completion Time We estimate that it will take 30 minutes to perform this procedure. Keep all hardware organized as you work. WARNING: Please have a certified electrician check voltages on the power su...