Customer Part Installation Instructions

Wiring Changes Required to add an all-in-one RFID Reader and Antenna to an Auto Sentry PetroTools RequiredPrior to performing this procedure, you will need to have the following tools:Small slotted screwdriverWire cutterTime to CompletionWe estimate that it will take 15 minutes to perform this pr...

In the box, find the new PETRO door panel and baggie of included parts. Open the right door of the PETRO.  Turn OFF the PETRO. Remove the plastic from the door.  There are 4 screws holding it on the inside of the door, and two bezels for the door locks on the front. Remove any and all wire clamps...

PETROMB170WIN7Motherboard upgrade for Auto Sentry Petro First it must be determined whether the PETRO has an SIO board or an older PIO board. This can be accomplished by looking at the cables going to the top of the motherboard that is presently installed (See images below) The SIO cable in the P...

Tools IncludedPrior to performing this procedure, you will need to have the following tools: 5/16” nut driver or ratchet 7/16” nut driver or ratchet #1 Phillips screw driver Completion TimeWe estimate that it will take 60 minutes to perform this procedure. Keep all hardware organized asyou work.W...

Part IdentificationReview parts list below prior to making any connections.   DescriptionICS Part CodeA8” CSD Touch ScreenKRC54170117B24V DC Power SupplyN/A - Included with CSDCDB9 / RJ45 Serial Interface CableKRC54160010DDB9 Serial CableCBLINPUTEDB9 Surge ProtectorSURGECOMFDB9 / RJ45 Serial Adap...

BD3NMD50/400HWDeLaRue BDNMD50 Bill DispenserTo Fujitsu F400 Bill Dispenser Conversion KitPowering Down the Auto Sentry flexWARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily injury or death;and also, may cause the credit card reader to go into a tamper state and if ...

Tools RequiredYou will need to have the following tools:Small Flathead Screwdriver.Completion TimeWe estimate that it will take 15 minutes to perform this procedure. Keep all hardware organized as you work.WARNING: This process needs to be completed while the Smartstart is powered down.Instructio...

Wiring the eKeypadfor Vacuums and Self-Serve Bays     There are two different power wiring options for the eKeypad:   Option A: 12v/24v DC Option B: PoE (Power over ethernet)   WARNING!    DO NOT wire both 12v/24v DC and PoE at the same time           Please contact ICS Technical Support if an...

  Tools Required Parts Included Powering Down the Entrance Sign WARNING: Failure to turn off the Sign increases the risk of serious bodily injury or death. On the site server desktop, click on the VNC icon for the Entrance Sign. On the menu bar, click the Windows flag icon. Click the Shutdown ...

REPLACING ENTDISPLAY46CC3 IN AN ENTRANCE SIGN Tools Required Prior to performing this procedure you will need to have the following tools:  #2 Phillips screwdriver  Small flat screwdriver Time to Completion We estimate that it will take 1 hour to perform this procedure, time will vary based on ...

Converting a Fujitsu F400Bill Dispenser Cassetteto runForeign Paper Currency The Fujitsu F400 bill dispenser cassettes come preset for U.S. paper currency.Inside the cassette, the paper currency rides on two plates. There is one on each side of the cassette, running lengthwise in the cassette. At...

Genmega Bill Dispenser Conversion from De La Rue Bill Dispenser WARNING: If you have the 3-pin power harness connector, go to the section on 3-pin to 10-pin power conversion on page 10 and use power pigtail cable AS3CBL29.  YOU MUST MAKE THE WIRING CHANGES AT THE POWER SUPPLY AS ILLUSTRATED. Tool...

Parts Included  Power Down the Auto Sentry flexWARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily injury or death;and also, may cause the credit card reader to go into a tamper state and if that happens, the credit card reader will have to be replaced.On the site se...

    Replacing USB Credit Card Reader for all Auto Sentry Models     Completion TimeEstimated time to complete this procedure is 15 minutes. Keep all hardware organized as you work. Powering Down the Auto Sentry WARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily inj...

Auto Sentry Conversion from TXP IDTech Card Reader to First Data IDTech Card Reader and Front Facing Barcode Scanner Tools Required Prior to performing this procedure you will need to have the following tools: 5/16”, 11/32” and 3/8” nut drivers or ratchets Drill with 3/16” and ½” drill bits Jig ...

Tools Needed: #1 Phillips screw driverNOTE: Keep all hardware organized as you work. Completion TimeWe estimate that it will take 30 minutes to perform this procedure. Keep all hardware organized asyou work.WARNING: Please have a certified electrician check voltages on the power supply beforeinst...

Installation of the Update to the Digital Menu Sign Video Board Controller Panel       Completion Time Estimated time to complete this procedure is one hour. Keep all hardware organized as you work. WARNING: Please have a certified electrician check voltages on the power supply before installin...

ENTRANCE SIGN CONVERSIONENT1-07 to ENT1-03 byADDING A MOTHERBOARDMB03 Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver Time to Completion We estimate that it will take 15 minutes to perform this procedure, time will vary based on...

Digital Menu Sign ENT1-07 converting it to an Exit Sign ENT1-03 by adding a motherboard Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver Time to Completion We estimate that it will take 15 minutes to perform this procedure, time ...

Adding an ALR9900+ RFID Reader to an Auto Sentry Petro Tools Required Prior to performing this procedure you will need to have the following tools: Small slotted screwdriver Wire cutter #2 Phillips screwdriver Antenna wire crimper kit ¼” and 11/32” sockets or wrenches Time to Completion We esti...

Vandalism Deterrent Alarm Installation in the Auto Sentry flex HD         Completion Time We estimate that it will take 15 minutes to perform this procedure. Keep all hardware organizedas you work. Powering Off the Auto Sentry   WARNING: Failure to turn off the Auto Sentry increases the ris...

  SETTING THE BACKLIGHT PARAMETERS ON AN ENT1-01, ENT1-02, and ENT1-03 WITH THE ENTDISPLAY46CC1/CC2 CONTROLLER Time to Completion ICS estimates that it will take 15 minutes to perform this procedure, time will vary based on skill set.   Parts Included – RS232 Adapter with Cable WARNING - THIS P...

Auto Sentry flex upgrade from Spectrum Air TXP to IDTech VP5300           Completion Time Estimated time to complete this procedure is 2 hours. Keep all hardware organized as you work. WARNING: Please have a certified electrician check voltages on the power supply before installing new compone...

Replacing Bar Code Reader with Bar Code Scanner in an Auto Sentry Tools Required Prior to performing this procedure, you will need to have the following tools: Phillips Screw driver 3/8” nut driver or ratchet Drill with 5/32” drill bit Jigsaw Vacuum cleaner, towel Small sharp knife Small sander ...

Auto Sentry Conversion to the Bezel Credit Card Reader Tools Required Prior to performing this procedure you will need to have the following tools: Small, sharp knife 3/8” nut driver or ratchet 11/32” nut driver or ratchet Time to Completion We estimate that it will take 2 hours to perform this...

Calibrating the Car Sense Green Electric Eye Sensor Auto Sentry Flex or Auto Sentry Petro Tools Required Prior to performing this procedure, you will need to have the following tools:Tape Measure Completion Time We estimate that it will take 5 minutes to perform this procedure. Keep all hardware ...

  AUTO SENTRY CPT CONDENSATE DRAIN HOSE CONFIGURATION Tools Required Prior to performing this procedure you will need to have the following tools:  11/32” nut driver or ratchet   Time to Completion We estimate that it will take 15 minutes to perform this procedure, time will vary based on ski...

CONFIGURING A GEN MEGA BILLDISPENSER CASSETTEFOR THE TOP OR BOTTOM LOCATION   Completion Time We estimate that it will take 15 minutes to perform this procedure. Keep all hardware organizedas you work. Instructions This procedure only needs to be completed if you are changing the location of the...

REPLACING THE VERIFONE CARD READER WITH AN IDTECH CARD READER   Tools Required Prior to performing this procedure you will need to have the following tools: #2 Phillips Screw driver sharp utility knife 3/8” nut driver or ratchet 11/32” nut driver or ratchet 5/16” nut driver or ratchet Time to C...

Gen Mega Bill Dispenser Power Cable Conversion 3-pin to 10-pin Power CableTools RequiredYou will need to have the following tools:Parts IncludedCompletion TimeICS estimates that it will take 15 minutes to perform this procedure. Keep all hardware organizedas you work.Powering Down the Auto Sentry...