Customer Part Installation Instructions

Truck Bed Sensor InstallationUsing Terminal Blocks and CPU Board with onboard Converter     Completion Time Estimated time to complete this procedure is 60 minutes. Keep hardware organized as you work. WARNING: Please have a certified electrician check voltages on the power supply before insta...

Auto Sentry® Conversion from TXP ID TECH® Card Reader to Fiserv (FIRST DATA) / Heartland ID TECH® Card Reader and Contactless Card Reader   WARNING: DO NOT install this hardware unless instructed to do so afterconsulting an ICS technician. Powering on this hardware in the wrong way maycause it to...

Auto Sentry Petro Conversion from the TXP Card Reader to an IDTech Card Reader   WARNING: Please have a certified electrician verify 24 volts on the power supply before installing any new components.   Completion Time It will take an estimated 2 hours to perform this procedure; time will vary ...

F400 to Genmega Bill Dispenser Conversion WARNING: If the F400 bill dispenser you are removing has a direct power cable to the power supply, use the power pigtail cable AS3CBL29 and power harness cable AS3CBL03D. YOU MUST MAKE THE CORRECT WIRING CONNECTIONS AT THE POWER SUPPLY AS ILLUSTRATED. ...

AUTO SENTRY PETRO CONVERSION TXP CARD READER TO VERIFONE CARD READER   Tools Required Prior to performing this procedure, you will need to have the following tools: 3/8” AND 11/32” nut driver or ratchet Wire cutter for cutting wire ties #2 Phillips screw driver Time to Completion We estimate th...

  Owners and Operators, Accompanied with this letter is a recovery flash drive for your Auto Sentry or Touch IT (Input Terminal). It will be necessary to contact ICS Support to perform the update (800-246-3469). Please set aside an hour per device to perform the upgrade. It will be necessary to h...

 Auto Sentry flex Moneris® Retrofit   Before you beginThere are a few things to consider before you begin the Retrofit.The Coin Acceptor will need to be removed and cannot be reinstalled.The Gift Card Dispenser and Gift Card Chute will need to be removed andcannot be reinstalled.You will need a s...

Tools RequiredPrior to performing this procedure you will need to have the following tools:#2 Phillips screwdriverTime to CompletionWe estimate that it will take 30 minutes to perform this procedure, time will vary based on skill set.NOTE: Keep all hardware organized as you work. Parts Included P...

Genmega Bill Dispenser Conversion from MultiMech Bill Dispenser WARNING: If you have the 3-pin power harness connector, go to the section on 3-pin to 10-pin power conversion INSTR0098 on page 10 and use power pigtail cable AS3CBL29.  YOU MUST MAKE THE WIRING CHANGES AT THE POWER SUPPLY AS ILLUSTR...

BD3MM/NMD50HWBD3MM/NMD50DHWMultiMech Bill Dispenser toDeLaRue Single or DualConversion Kit Turn off the Auto Sentry. Disconnect power to the Auto Sentry.Open the base door of the Auto Sentry. Disconnect the power and data cables from the MultiMech bill dispenser. Remove the MultiMech bill dispens...

ITPRCBL for Printer Cable Installation In KEYPAD1-0-A  Tools IncludedPrior to performing this procedure, you will need to have the following tools: SEALTIGHT01 cable glandITPRCBL printer cable Tools RequiredPhillips screwdriverFlat screwdriver 1/8” drill bit ¾ “ drill bitAdjustable wrenchParts In...

HOW TO REPLACE A DeLaRue BILL DISPENSER IN AN AUTO SENTRY WITH A MULTI-MECH BILL DISPENSER IF THE DeLaRue HAS A 3-PIN POWER PIGTAIL CABLE Completion TimeWe estimate that it will take 30 minutes to perform this procedure. Keep all hardware organized asyou work.WARNING: Please have a certified elec...

ITPRCBL – change in cable   Please contact ICS Technical Support if any assistance is needed: 800-246-3469            INSTR0052 

Tools NeededPrior to performing this procedure you will need to have the following tools:Drill with 3/32” (for #6 PEM studs), 1/8” (for #8 PEM studs, 7/32” (for #10 PEM studs) drill bitsCenter punchRatchet with 5/16” (for #6 PEM studs), 11/32” (for #8 PEM studs), or 3/8” (for #10 PEM studs) socke...

Required ToolsPhillips Head Screw DriverRemove Existing Circuit BoardRemove Input Terminal lid by loosening the (4) phillips head screws and carefully lifting it off base. There are rubber washers on the inside of the screws. Make sure to save them, they will be used when the lid goes back on. Un...

Tools NeededPrior to performing this procedure, you will need to have the following tools: Phillips screwdriver Powering Down the Auto Sentry flexWARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily injury or death;and also, may cause the credit card reader to go into...

Tools NeededPrior to performing this procedure, you will need to have the following tools: Phillips screwdriver 11/32” nut driver or socket wrenchPowering Down the Auto Sentry flexWARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily injury or death;and also, may cause...

Required Tools Phillips Screw Driver11/32 Nut driver or socket wrenchRemove Coin Hopper ShelfSlide out coin hopper shelf.Remove cables from coin hopper board.Unhook cable chain from shelf. Lift tabs on sides of shelf, remove shelf, and place aside. Replace Hecon PrinterRemove power and USB cable ...

Before You BeginAlways turn the power to the unit off before you begin.Read all instructions first.A qualified ICS technician can help ensure these instructions are followed correctly. Required ToolsAdjustable Wrench7/16” Nut driverReplacing BezelUse adjustable wrench to loosen to loosen nut. Rem...

   Please contact ICS Technical Support if any assistance is needed: 800-246-3469    INSTR0060

Powering Up the Auto Sentry flexTurn on the electricity to the Auto Sentry Flex by turning on the Auto Sentry breaker inside the ICS power distribution box.Turn the breakers on inside the Auto Sentry flex by pressing the blue buttons on the breakers until they click in.Inside the Auto Sentry flex...

Tools NeededPrior to performing this procedure, you will need to have the following tools: Phillips screwdriver #23/8" Nut driver or socket wrenchPowering Down the Auto Sentry flexWARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily injury or death;and also, may cause...

Tools NeededPrior to performing this procedure, you will need to have the following tools: Phillips screwdriver 11/32” nut driver or ratchet Powering Down the Auto Sentry flexWARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily injury or death;and also, may cause the ...

Required ToolsPhillips Head Screw DriverSmall Flat head screw driverNeedle-nose pliersRemoving Existing Main BoardPower to the unit off before you begin.Remove cover by removing the (3) bolts securing it to head.Remove expansion board from existing main board by using needle-nose pliers to pinch ...

Required ToolsStandard Phillips screwdriver11/32" Nut driverPowering Down the Auto Sentry flexWARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily injury or death;and also, may cause the credit card reader to go into a tamper state and if that happens, the credit card...

Tools NeededPrior to performing this procedure, you will need to have the following tools: Phillips screwdriver 3/8" Nut driverPowering Down the Auto Sentry flexWARNING: Failure to turn off the Auto Sentry increases the risk of serious bodily injury or death;and also, may cause the credit card re...

Tools Required#2 Phillips screwdriver11/32" Nut driver or socket wrenchZip ties (To replace ones that will be cut) Completion Time It will take 45 minutes to perform this procedure based on skill set. Keep all hardware organized as you work.Powering Down the Auto Sentry flexWARNING: Failure to tu...

      Completion Time Estimated time to complete this procedure is 2 hours. Keep all hardware organized as you work. WARNING: Please have a certified electrician check voltages on the power supply before installing new components. The voltage should be 24 volts.   Shutting Off the Power to the...

  Completion Time We estimate that it will take 2 hours to perform this procedure. Keep all hardware organized as you work.The screws and washers removed will be used again in the installation of the new Display Panel. Pleasecompletely read each step before performing.WARNING: The wiring and te...

    Completion Time Estimated time to complete this procedure is 2 hours. Keep all hardware organized as you work.WARNING: Please have a certified electrician check voltages on the power supply beforeinstalling new components. The voltage should be 24 volts. Shutting Off the Power to the Entra...