Customer Part Installation Instructions

Auto Sentry Petro Camera Replacement Tools Required Prior to performing this procedure you will need to have the following tools: Small Flat Screw driver Time to Completion We estimate that it will take 15 minutes to perform this procedure, time will vary based on skill set.NOTE: Keep all hardw...

Replacing Comm Card in Comm box with a Serial Adapter for Tunnel Master Server   Tool Needed Small Screw Driver Parts Used You will used the Existing Comm wire from the Input Terminal to the comm box and the existing serial cable from the Tunnel Master server to Comm box. Prior to performing this...

Replacing the FIRST DATA VERIFONE UX300 CARD READERin an Auto Sentry flex or an Auto Sentry flex HD WARNING: Please have a certified electrician verify 24 volts on the power supply before installing any new component. Completion TimeWe estimate that it will take 1 hour to perform this proce...

Verifone UX301 Installation Procedure for the Auto Sentry Petro We estimate that it will take 1 hour to perform this procedure, time will vary based on skill set. NOTE: Keep all hardware organized as you work. All hardware removed will be used again during re-install. Required Tools: Flat screwd...

Replacing the IDTECH VP5300 in an Auto Sentry flex and Auto Sentry flex HD   WARNING: Please have a certified electrician verify 24 volts on the power supply before installing any new component.   Completion Time We estimate that it will take 1 hour to perform this procedure, time will vary b...

Auto Sentry Petro 2nd Gen 15” Display Installation Completion Time We estimate that it will take 60 minutes to perform this procedure. Keep all hardware organizedas you work. WARNING: Please have a certified electrician check voltages on the power supply before installing new components. The vo...

Auto Sentry flex Display Panel Assembly Replacement(standard and high security models) Tools Required Prior to performing this procedure you will need to have the following tools: Flat screwdriver Phillips screwdriver #2 Hand Ratchet with a ¼” drive 6” Wobble Extension for a ¼” drive ¼” drive so...

Touch IT Display Replacement   Instructions to Power Down the Touch IT WARNING: Failure to turn off the Touch IT increases the risk of serious bodily injury or death. On the Touch IT screen, click the Shutdown button to turn off the operating system, and wait until a white screen appears. Ope...

Replacing the First Data ID Tech Card Reader in an Auto Sentry flex   Tools Needed: 3/8”, 11/32”, and 5/16” nut driver or ratchet Time to Complete We estimate that it will take 1 hour to perform this procedure, time will vary based on skill set. NOTE: Keep all hardware organized as you work. Pl...

This procedure instructs on how to replace the Hard Drive in a Touch IT. Touch IT Hard Drive Replacement   Power Down the Touch IT WARNING: Failure to turn off the Touch IT increases the risk of serious bodily injury or death. On the Touch IT screen, click the Shutdown button to turn off the ...

REPLACING THE HEAT EXCHANGER EXTERNAL FAN IN A TOUCH IT Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver Wire cutter, wire stripper, wire crimper 11/32” nut driver or socket Soldering iron and electrical tape or wire connectors (p...

 WARNING: Please have a certified electrician check voltages on the power supply before installingnew components. The voltage should be 12v.Tools RequiredYou will need to have the following tools: Tools Included Completion TimeWe estimate that it will take 2 hours to perform this procedure. Keep ...

Installing and Programming the IFM Car Sensor Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver 2 adjustable wrenches Time to Completion We estimate that it will take 1/2 hour to perform this procedure, time will vary based on ski...

Touch IT Mano Motherboard and Hard Drive Replacement      Instructions to Power Down the Touch IT WARNING: Failure to turn off the Touch IT increases the risk of serious bodily injury or death. On the Touch IT screen, click the Shutdown button to turn off the operating system, and wait unti...

Tools RequiredPrior to performing this procedure you will need to have the following tools:#2 Phillips Screw driver11/32” nut driver or ratchet5/64” hex bit or driverClean towels or a clean work surfaceTime to CompletionWe estimate that it will take 2 hours to perform this procedure, time will va...

Entrance Sign Motherboard Replacement   Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver   Time to Completion We estimate that it will take 30 minutes to perform this procedure, time will vary based on skill set.NOTE: Keep all ha...

Touch IT Power Port Replacement   Introduction Please read the entire procedure before proceeding. There are three possible wiring scenarios for thepower port replacement in the Touch IT. For Versions 1 and 2, the power port wires will go to the sameterminals on the white terminal block as the...

Replacing a Cosel Power Supply with a VOX Power Supply in an Auto Sentry flex or an Auto Sentry flex HD     WARNING: Please have a certified electrician verify 24 volts on the power supply before installing any new component. Tools Needed   Completion Time We estimate that it will take 1 hour...

Replace the RFID Circuit Board and Cable in an All-in-one RFID Antenna     Completion Time WARNING: THIS PROCEDURE WILL REQUIRE YOU TO WORK ABOVE GROUND ON A LADDER AS YOU REMOVE AND REPLACE THE BOTTOM COVER OF THE ANTENNA ENCLOSURE. PLEASE TAKE YOUR TIME AND WORK SAFELY. We estimate that it w...

Replacing the RFID circuit board and cable in an all-in-one RFID antenna.   Completion Time We estimate that it will take 30 minutes to perform this procedure. Keep all hardware organized as you work.   WARNING: THIS PROCEDURE WILL REQUIRE YOU TO WORK ABOVE GROUND ON A LADDER AS YOU REMOVE AND ...

Touch Screen Replacement in a 42 inch Entrance Sign Tools Required Prior to performing this procedure, you will need to have the following tools: Long #2 Phillips screw driver Regular #2 Phillips screw driver Small flat screw driver A second person to assist at times Time to Completion We estim...

Touch Screen Replacement in a 42" Entrance Sign Tools Required Prior to performing this procedure you will need to have the following tools: Long #2 Phillips screw driver Regular #2 Phillips screw driver Small flat screw driver A second person to assist We estimate that it will take 2 hours to ...

Replace the yellow clips on the Top Denomination Pick Assembly       Time to Completion We estimate that it will take 15 minutes to perform this procedure, time will vary based on skill set. NOTE: Keep all hardware organized as you work.   Powering Off the Auto Sentry On the site server deskto...

Adjusting the Cooling and Heating Settings on the ICEQUBE Air Conditioner to an ICS® Entrance, Exit, or  Menu Sign   Time to Completion We estimate that it will take 30 minutes to perform this procedure, time will vary based on skill set.NOTE: Keep all hardware organized as you work. While the po...

Wash Valet eXP Genmega Bill Dispenser Upgrade from Fujitsu F100/F400 OR De La Rue Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver 3/8” nut driver or ratchet 11/32” nut driver or ratchet Time to Completion We estimate that it wil...

Replacing the Auto Sentry flex Rear Door Heat Exchanger Drip Cup   Completion Time Estimated time to complete this procedure is 5 minutes. Keep all hardware organized as you work. WARNING: The Auto Sentry flex is still powered on, BE CAREFUL! Replacing the Drip Cup Using the hex key, open the l...

AUTO SENTRY FLEX ATTACHING THE CARD READER FRONT BEZEL WITH SCREW STUDS TO RE-INSTALL THE CARD READER Tools Required You will need to have the following tools: Time to Completion We estimate that it will take 1 hour to perform this procedure, time will vary based on skills. Keep all hardware org...

TNCDISPUPDATE Replacement Display for the Auto Sentry Petro (Prior Petro model only) and the Touch'N'Clean     Tools Required Prior to performing this procedure you will need to have the following tools:          11/32” nut driver or ratchet Parts Included (door and speaker not included)   Com...

Auto Sentry Petro Upgrade to add Vibration Sensor Tools Required Prior to performing this procedure you will need to have the following tools: Phillips Screw driver Wire cutter for cutting wire ties Time to Completion We estimate that it will take 1 hour to perform this procedure, time will var...

Adjusting the rear belts in a Fujitsu Bill Dispenser Pick Assembly Tools Needed: Small Phillips screwdriver Time to Completion We estimate that it will take 10 minutes to perform this procedure, time will vary based on skill set. NOTE: Keep all hardware organized as you work. WARNINGS: Power d...